Borough Park Mold Inspection and Mold Testing
Borough Park grew from the hamlet of Blythebourne, which Electus Litchfield developed in 1887. In 1902, William H. Reynolds bought land and named the area Borough Park, and Jewish immigrants began settling here in 1904 and 1905. By the 1920s, Blythebourne had been absorbed into the larger neighborhood. Today Borough Park is home to many large families, and demand for bigger homes has led to extensive expansions and renovations, especially larger bedrooms and kitchens; a 1992 zoning change allowed building on 65 percent of a lot. 13th Avenue, a roughly one-mile shopping strip between 39th and 55th Streets, draws shoppers from across the city. The 2010 Census counted 106,357 residents, according to figures reported for the neighborhood.
Prime Environmental NY provides independent mold testing in Borough Park, Brooklyn and professional mold inspection for homeowners, multi-family owners, tenants, buyers, schools, and businesses. We inspect, test, and report. We do not perform mold remediation, removal, or construction.
Call (917) 723-2297 or email primeenvironmentalny@gmail.com to schedule mold testing in Borough Park.
Borough Park at a Glance
- Community district: Brooklyn Community District 12
- ZIP codes: primarily 11219, with parts of 11204, 11218, 11220, and 11230
- Neighbors: Bensonhurst, Dyker Heights, Sunset Park, Kensington, Flatbush, and Mapleton
- Main commercial street: 13th Avenue
- Housing: homes with extensive expansions and renovations, multi-family buildings, and apartment buildings
Expansions, Additions, and Moisture
When homes are enlarged, new construction is joined to old. Those joints are among the most common places for water to get in:
- Roof tie-ins where a new roof section meets the original roof
- Wall transitions where new exterior walls meet older masonry or siding
- Windows and doors installed in new openings
- New bathrooms and kitchens placed above rooms that previously had no plumbing overhead
- Basements enlarged or finished during renovation, where drainage and waterproofing may not match the new layout
Large households also generate more indoor moisture from cooking, showers, and laundry. If ventilation was not upgraded along with the house, humidity can build up and lead to condensation and growth in bathrooms, kitchens, and closets.
Kitchens in Busy Homes
Bigger kitchens, often with more than one sink and dishwasher, are a hallmark of Borough Park renovations. Each additional appliance and plumbing fixture is another potential leak point. During an inspection, we check under sinks, behind and beneath dishwashers, around refrigerator water lines, and at the ceiling below the kitchen when it sits over living space. We also check whether range hoods vent outdoors.
Mold Testing Services
Professional Mold Inspection
A visual assessment of the accessible areas in your scope for suspected microbial growth, water damage, and conditions that support mold.
Moisture Investigation
Moisture readings and observations focused on plumbing leaks, roof leaks, flooding, condensation, humidity, and water intrusion.
Mold Air Sampling and Mold Spore Testing
Indoor air samples, with an outdoor comparison sample when conditions allow, analyzed by a laboratory that identifies and counts airborne fungal spores.
Mold Surface Sampling
Swab and tape-lift samples from suspect surfaces, sent for mold laboratory analysis. This is the reliable answer to black mold testing questions.
Basement Mold Inspection and Attic Mold Testing
Inspection and sampling in accessible lower levels, attics, and roof spaces.
Indoor Air Quality Testing
Mold-focused indoor air quality testing pairing air sampling with inspection findings.
Post-Remediation Mold Verification
After remediation by a separate contractor, an independent visual inspection and appropriate sampling assess whether evaluated areas meet the applicable clearance criteria.
Commercial Mold Inspection on 13th Avenue
Shops, restaurants, bakeries, groceries, schools, and offices along 13th Avenue and nearby streets often occupy older buildings with basements and apartments above. Commercial mold inspection focuses on storage areas, kitchens, restrooms, below-grade rooms, and ceilings beneath upper floors. We can schedule around business hours, Shabbat, and holidays when you let us know your preferences.
Rental Buildings
For residential buildings with three or more apartments, New York City’s Department of Housing Preservation and Development (HPD) explains that Local Law 55 requires owners to keep units free of mold, inspect units annually for indoor allergen hazards, and make sure vacant units are free of mold before new tenants move in. Tenants and owners can both hire us to evaluate areas they can access.
NYS Licensed Mold Assessment
Prime Environmental NY’s mold assessment work is performed under New York State Department of Labor licenses:
- Mold Assessment Contractor License: 26-693HR-SHMO (issued to Prime Environmental NJ LLC)
- Mold Assessor License: 26-69JDH-SHMO (individual license of Korab Ibrahimaj)
Both are listed in the state’s mold license records on data.ny.gov. New York does not allow one licensee to both assess and remediate a project, and we only assess and test.
Ventilation for Large Households
- Run bathroom exhaust fans during every shower and for at least 20 minutes afterward, and confirm they vent outdoors.
- Use a range hood that vents outside when cooking.
- Make sure dryers vent outdoors and dryer ducts are intact.
- Avoid drying laundry indoors in closed rooms.
- Keep furniture a few inches from exterior walls so air can circulate.
- Monitor humidity; the U.S. Environmental Protection Agency recommends keeping it below 60 percent, ideally 30 to 50 percent.
Construction Moisture in Renovated Homes
Renovation projects can introduce moisture that becomes a problem later. Lumber, drywall, and insulation can get wet from rain while a roof or wall is open, concrete and plaster release moisture as they cure, and plumbing connections made during construction can leak slowly once the walls are closed. If materials were enclosed before they dried, growth may develop behind finishes without anything visible at first. Early signs include musty odors in newly finished rooms, paint that bubbles or peels soon after it was applied, and staining near new plumbing fixtures. During an inspection, we take moisture readings in renovated areas, look at transitions between old and new construction, and sample where useful. If the evidence suggests hidden moisture, our findings will say so.
Understanding Air Sampling Results
Mold spores are always present outdoors, so indoor results are compared with an outdoor sample collected at the same time. Indoor totals well above outdoor levels, or spore types rare outdoors, can point to an indoor source. Interpretation always considers what we observed and measured during the inspection.
What Your Findings Include
When a written report is part of your service, it lists the areas evaluated and any that could not be accessed, documents observed conditions with photographs, summarizes moisture readings and likely sources, presents laboratory results with interpretation, and recommends practical next steps.
How the Inspection Works
We start with a phone call about your concerns, renovation history, and which areas to include. On site, we review the home with you, inspect, take moisture readings, photograph conditions, and collect samples according to the scope. Samples go to a laboratory, with turnaround based on the service level selected. When a written report is part of your service, it includes laboratory results, interpretation, observed conditions, and recommendations.
Preparing for Your Visit
- Leave suspect areas uncleaned and unpainted.
- Keep windows closed as usual before air sampling.
- Clear access to the basement, attic hatch, and kitchen and bathroom cabinets.
- Gather dates of renovations, leaks, and roof work.
Signs Worth a Professional Look
- A musty smell in the basement, a closet, or a bedroom
- Ceiling stains below kitchens or bathrooms
- Staining where an addition meets the original house
- Spotting on bathroom ceilings that keeps returning
- A leak that was not dried quickly
Borough Park Mold Testing FAQ
We recently renovated. Can mold already be a problem?
Yes, if leaks occurred during construction or materials were enclosed while still wet. An inspection with moisture readings can help clarify current conditions.
Can you schedule around Shabbat and holidays?
Yes. Let us know your preferred days and times when you call.
Do you remove mold?
No. We provide independent inspection and testing only.
Which nearby areas do you serve?
Bensonhurst, Kensington, Midwood, Dyker Heights, Sunset Park, and all of Brooklyn.
Related Pages
See our Bensonhurst, Dyker Heights, and Brooklyn pages, plus our mold testing and mold inspection services.
Schedule Mold Testing in Borough Park, Brooklyn, NY
For an independent mold inspector in Borough Park, Brooklyn, NY, contact Prime Environmental NY.
Prime Environmental NY
Phone: (917) 723-2297
Email: primeenvironmentalny@gmail.com
Business Address: 22-20 78th St, East Elmhurst, NY 11370 (inspections by appointment at your property)
Independent Mold Inspection and Testing Only — No Mold Removal or Remediation.